How far away from the wall does a pellet stove have to be?

The outer surfaces of a pellet stove don’t get as hot as the surfaces of wood stoves or fireplaces, so most can be placed closer to combustibles—typically 3 inches from walls at the sides and 1 inch from a back wall. Most need to stand on a non-combustible surface such as stone or tile that is at least 3/8 inch thick.

How high does a chimney need to be for a pellet stove?

A chimney should extend at least 3 feet above the roof opening and be at least 2 feet higher than any point of the roof or building within 10 feet.

Do pellet stoves require venting?

Venting: Unlike wood stoves, pellet stoves do not need a chimney and can be vented out through a side wall. This allows for more flexibility on the installation and also reduces the overall installation costs. Pellet stoves can be hooked up to existing chimneys.

Where should I put my pellet stove?

Placing a pellet stove next to an exterior wall is always ideal because this kind of setting will reduce ventilation costs. Typically, a Pellet stove is installed approximately 1-2 inches from a wall, so the vent can travel out the back of the stove and through a rear wall.

Can you vent a pellet stove straight out a wall?

Pellet stoves can be vented vertically through the roof or horizontally through a side wall. Never use PVC pipe, gas vent pipe, dryer vent pipe or single wall black stove pipe to vent your pellet stove.

Can you put a pellet stove in front of a window?

Installing A Pellet Stove: Windows And Doors The rule is that a pellet stove must not terminate within four feet to the side or below opening windows or doors. This can be reduced to 18 inches if the stove uses an external air source for combustion. It is possible to place a pellet stove underneath a window.

Can a pellet stove use an existing chimney?

A: You can vent a pellet stove either through a wall or through an existing masonry chimney. Some chimneys also require the installation of an approved metal liner that the pellet stove vent pipe passes through.

How tall should my chimney be?

The most common of these being the 2 foot, 10 foot, 3-foot rule. Roughly this means that a chimney should be 3 feet higher than the point it passes through a roof, while also being at least 2 feet taller than any part of a building that’s within 10 feet of the chimney.

Do all pellet stoves require outside air?

Do All Pellet Stoves Need Outside Air? Not all pellet stoves require an external fresh air intake vent but may be required depending on local building codes and regulations, and many manufacturers recommend venting fresh air externally for pellet stoves.

Is there a ventless pellet stove?

Pellet stoves produce waste exhaust that must be vented to the outside; therefore, vent-free pellet stoves do not exist. They require a specific type of sealed exhaust pipe to send the bad air out.

Can I put a pellet stove in the middle of the house?

You can place your wood pellet stove against a wall, the center of a room, or choose a corner model that fits well in tight spots. A pellet stove in the center of the room will warm the room quickly, but it may not be practical for high-traffic areas or in rooms that are cramped.

Will a pellet stove in basement heat House?

A pellet stove installed in your basement does not circulate heat around your house as efficiently as a furnace with an electric fan and dedicated ducts. Cutting a few vents in the floor can certainly help. But you’re still relying on natural convection for heat distribution.

Where can I install a pellet stove?

Installing your pellet stove near a stairway is an ideal location because it provides heat to the upper and lower levels of your home. The best placement within the room is near an exterior wall so you can vent the pellet stove directly outside.

How far from the wall does a pellet stove need to be?

A pellet stove is typically installed just 1 to 2 inches away from a rear wall, but you can install it farther out if you like. The vent can travel out the back of the stove through the wall, making it inconspicuous if not nearly invisible.

What size vent pipe do I need for a pellet stove?

If installing your pellet stove venting at 2,500 feet or more above sea level, you definitely need four inch pipe. This is because at this altitude the oxygen level in the air is lower and the stove needs to push more air through to burn effectively.

What is the best way to vent a pellet stove?

Horizontal venting is the simplest and cheapest way to remove the exhaust gases from your pellet stove. The vent pipe is connected to an adapter at the back of the stove, then run out through the wall adapter plate to a distance of at least six inches from the exterior wall.