Where is the PCM located on a 2004 Jeep Grand Cherokee?

Where is the PCM located on a 2004 Jeep Grand Cherokee?

The coolant reserve/overflow tank will be in the way but the location of the PCM is on the cowl panel in the right/rear side of the engine compartment.

How do you tell if Jeep PCM is bad?

1. Identifying Jeep PCM failure.
2. Vehicles fail or roughly starts.
3. Systematic loss of gas mileage.
4. Stalling or stuttering engine.
5. Vehicle randomly shifts.
6. Failure in emission tests.
7. PCM DTC codes keep appearing on the diagnostic device.

Where is the PCM located on a 05 Jeep Grand Cherokee?

Open up the hood and take a look into the far left corner, it is up against the left wall you will see it. It’ll most likely be covered up with heat sinks.

How do you reset the PCM on a Jeep Cherokee?

Disconnect the battery by removing the positive battery cable. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors. Reconnect the positive cable to the battery. Turn the key to on but do not start.

What is PCM on Jeep Grand Cherokee?

The Powertrain Control Module (PCM) is the computer that controls most of your Jeep’s essential systems. The PCM controls the engine timing, the fuel to air ratio, the transmission, and the anti-lock brakes, along with dozens of other smaller functions.

How much does it cost to replace a PCM?

In some cars, there are multiple computers, and with other cars, there are just a few. The PCM controls more than 100 factors in your car, and for that reason, is very important – and expensive. A typical pcm replacement cost comes to between $500 and $1,500 on average.

How do I reset my ECU Jeep Grand Cherokee?

Jeep ECU Reset Procedure

1. Disconnect the battery by removing the positive battery cable.
2. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
3. Reconnect the positive cable to the battery.
4. Turn the key to on but do not start.
5. Turn the headlights on.

How do I reset my Jeep computer?

Jeep Wrangler JK: How to Reset Your ECU

1. Step 1 – Remove the positive (red) battery cable.
2. Step 2 – Ground the red cable to the negative terminal.
3. Step 3 – Reconnect the positive battery cable.
4. Step 4 – Turn on your Jeep.
5. Step 5 – Cycle the headlights.
6. Step 6 – Turn the key off and remove.

Do you need to replace engine control module in Jeep Grand Cherokee?

Both capable and attractive, you’re Grand Cherokee is able to take you across country or cross-town. A vehicle like yours deserves to always function to the best of its ability, so pay attention for signs that you need to replace your Jeep Grand Cherokee engine control module.

Why does my Jeep Grand Cherokee not have a PCM?

One common problem that affects Jeep PCMs – particularly PCMs for the Jeep Grand Cherokee – is poor soldering on the 5-volt power connection. If all other tests have failed, you can try re-flowing the solder. We’ll go over this process in the next section.

Do you need a PCM for a 2007 Jeep Liberty?

When you’re searching for a replacement PCM, it’s important to keep in mind that PCMs are programmed for a specific make and model of vehicle. If you drive a 2007 Jeep Liberty with a 3.7-liter V6, you can’t use just any PCM. You can’t use just any Jeep PCM replacement. You need the PCM for that exact car.

How long does it take to repair a jeep PCM?

At Solo Auto, our dedicated technicians can repair your PCM and mail it back to you within 24 to 48 hours. Once you mail in your PCM, our technicians will assess the symptoms of your module, calibrate the codes, and conduct an internal and external inspection.